English
English 
| Category | Property | Typical Value / Description |
|---|---|---|
| Physical Properties | Density | 1.39–1.41 g/cm³ |
| Melting Point | 258–262°C | |
| Molding Shrinkage – Longitudinal | 0.2%–0.3% | |
| Molding Shrinkage – Transverse | 0.45%–0.6% | |
| Dimensional Stability | Far exceeds that of GF30 | |
| Equilibrium Water Absorption | 0.6%–0.8% | |
| Moisture & Heat Resistance | Resistant to warping and deformation under high temperature and humidity | |
| Mechanical Properties | Tensile Strength | 185–210 MPa |
| Flexural Strength | 285–305 MPa | |
| Flexural Modulus | 10,500–12,000 MPa | |
| Notched Impact Strength (Simply Supported Beam) | 9–13 kJ/m² | |
| Mechanical Performance | Significantly enhanced rigidity, fatigue resistance, and creep resistance; a lightweight alternative to small aluminum and cast iron components | |
| Heat Resistance | Heat Deflection Temperature (1.8 MPa) | 248–255°C |
| Heat Deflection Temperature (0.45 MPa) | 260–268°C | |
| Continuous Long-Term Operating Temperature | 115–135°C | |
| Short-Term Peak Temperature Resistance | 180–200°C | |
| Application Temperature Resistance | Suitable for sustained high-temperature conditions in engine compartments | |
| Chemical & Electrical Resistance | Chemical Resistance | Resistant to engine oil, gasoline, coolant, grease, and weak acids and alkalis |
| Strong Acid Resistance | Not resistant to concentrated strong acids | |
| Electrical Insulation | Excellent insulation properties | |
| CTI | ≥ 550 V | |
| Environmental Compliance | All grades comply with RoHS and REACH environmental standards |
Automotive Industry (Core Applications): Engine valve covers, intake manifolds, radiator water chambers, water pump housings, transmission structural brackets, small chassis suspension brackets, throttle body assemblies, fuel pump housings, and high-power automotive connector housings (oil-resistant, high-temperature-resistant, and hydrolysis-resistant).
High-Voltage Electronics and Electrical Equipment: Circuit breaker bases, high-power relay bases, internal load-bearing brackets for charging stations, motor coil frames, high-voltage terminal blocks, and insulated enclosures for variable frequency drives (flame-retardant V0-rated specialty material).
Power Tools & General Machinery: High-power angle grinder housings, impact drill gear sets, hydraulic pump valve bodies, heavy-duty bearing housings, industrial sprockets, small-to-medium precision transmission gears, and load-bearing housings for instruments and meters.
Other Industries: Load-bearing brackets for heavy-duty fitness equipment, small components for construction machinery, pressure-bearing valve bodies for bathroom fixtures, and transmission structural components for agricultural machinery.
High strength and low creep: 35% glass fiber reinforcement ensures minimal deformation under long-term pressure, making it suitable for parts subjected to prolonged heavy loads;
Excellent molding compatibility: Compared to GF40, it offers better flow properties and fewer free fibers, resulting in higher first-pass yield rates for complex deep-cavity and thick-walled large parts;
Comprehensive Modification Options: Hydrolysis-resistant grades for automotive cooling systems; V0 halogen-free flame retardant for high-voltage electrical applications; cold-resistant grades that do not crack at -35°C;
Precision and Low Shrinkage: Minimal dimensional change in high- and low-temperature environments, enabling controlled assembly tolerances for precision gears and snap-fit components.
Drying: Vacuum drying at 100–110°C for 4–6 hours, until moisture content is <0.12%, to eliminate silver streaks and air bubbles;
Barrel temperature: 270–290°C; nozzle temperature: 275–285°C;
Mold temperature: 90–110°C, to optimize surface finish, reduce fiber protrusion, and stabilize dimensional accuracy.
